Rns 149 manual

Hotkey, programmable function key. Info key. During route guidance press the Info key to have the last voice output for navigation repeated and the active destination dis- played.

The special information required by navigation systems for lorries or busses, such as height restrictions or maximum permissible loads, is not included on the navigation CDs. Operating the system while driving If you do not focus your full attention on the traffic situation at all times, you could cause serious accidents.

Page 7 Contents CD operation Page 8 Contents Special destinations in the destination Destination memory Page 9 Contents Track programming The system will begin to play the audio source which was active last at the power-on volume level. When you use one of these buttons to switch between the audio sources, you will access the main menu for the audio source selected.

Page Display General operating instructions Display The TravelPilot display provides you with all of the information required for nav- igation, such as the visual driving recommendations and the menus and lists for the radio, CD-player and CD-changer audio sources. If the system has been installed accordingly, it will automatically switch to night display when the vehicle headlights are switched on.

The settings selected for the balance, the fader and the Loudness are the same for all of the audio sources. Page Switching On Coded Systems After They Have Been Disconnected From The Vehicle Battery General operating instructions Switching on coded systems after they have been discon- nected from the vehicle battery f you attempt to switch on a coded system after it has been disconnected from the vehicle battery, e. Radio operation will begin and the main menu will appear in the display. The station you last tuned into will begin to play.

The six softkeys located at the sides of the display are used to recall the radio stations which have been stored as well as to store the radio stations. VAR is the default setting. OFF is the default setting. With PTY, the radio stations indi- cate the contents of the program they are broadcasting. If the TA function is activated for the other sources, CD player and CD changer as well as navigation , playback will be interrupted for an incoming traffic an- nouncement and the message will be broadcast.

Automatic station seek tuning To select radio stations automatically, on the rocker switch 7 to start station seek tuning upwards or Press on the rocker switch 7 to start station seek tuning downwards.

Automatic station seek tuning To select stations automatically, on the rocker switch 7 to start seek tuning up or Press on the rocker switch 7 to start seek tuning down. The system will tune into the next available station. Scan seek tuning will end, the station selected last will continue to play.

Page Storing Stations Automatically With "Travelstore Radio operation The system is able to store the six stations within reception range with the strong- est reception signals in the FMT memory bank. This function is particularly use- ful on longer trips. Please note that all of the stations previously stored in the FMT memory bank will be replaced by the new stations.

Use only audio CDs bearing this label: During CD playback, the display will indicate the track number and the playing time or only the track number in the top line of the main CD menu. The system will switch to the main CD menu and CD playback will begin.

If there is no audio CD inserted, a corresponding message will appear in the display. Press the softkey marked TA. Press CD. To end the MIX function, repeat these steps. The name can consist of up to seven characters. After the name has been stored, the system will switch to the CD function menu. The name will now appear in the functional display area of the main CD menu. Deleting characters If you want to delete a letter, Mark the This allows you to omit the tracks you do not want to play.

Creating the track program To create the track program, Press CD. Page Navigation Navigation RNS navigation enables you to find destinations quickly and easily without having to study a lot of road maps. When the navigation function is active, the voice output from the RNS will guide you along the best route. The system will warn you well in advance when you are required to make a turn.

Lists with more than five entries are marked with arrows on the right-hand side. Page Destination Entry - Town Navigation Destination entry - Town If you want to drive to a destination in another town, you must first enter the town.

Select DEST. The character will appear in the editing field. When the first character has been entered, the edit list will appear displaying the entries which begin with that character. When you enter an H as the first letter for your destination, for example, the edit list will move down to the names of places which begin with H Haader.

This allows you to find your destination in the edit list quickly. Deleting letters To delete a letter which you have entered by mistake, Mark the symbol and press OK 8 or the central softkey on the right side of the display.

Once the name of the place you want to enter as your destination appears on the edit list, Mark the symbol and Press OK 8 or Press OK 8 for longer than 2 seconds. The cursor will move to the list e. The desired entry will be marked. Lists with more than five on the right-hand side.

There are two ways to entries are marked with arrows access the other pages of a list: For lists with less than ten entries Press on the rocker switch 7 to move the selection bar to the secondlast entry. Each time you press , the contents of the list will move up by one line.

The selection bar will remain on the second-last entry and cannot be moved to the last entry until you have reached the end of the list. Scrolling through lists page-by-page List Route list for navigation with more than ten entries To find the entry you are looking for in long lists more quickly, you can also scroll through the list page-by-page.

The next or previous page of the list will appear in the display. The selection bar will remain positioned on the arrow symbol. Press OK 8 repeatedly until you reach the page you are looking for.

Select DEST. When the desired character is marked, press OK 8. The first place name on the list of towns and cities which begins with the letter selected will appear in the editing list. When the name of the town you want to select appears in the editing list, Mark the symbol and press OK 8, or Press down OK 8 for longer than two seconds.

The display will switch to the list of the place names. The name you want to select will be marked. Press OK 8 to select this place as your destination. If the name of the town or city is listed more than once, a submenu will appear. SURROUND, you can select special destinations directly from a list from such categories as motorway access, train station, shopping centre, etc.

For more information, refer to the section on Special destinations, Surrounding the destination. This will not be possible unless the corresponding data is available.

If there is no data available on individual menu items, these will be marked with a lock symbol and it will not be possible to select them. You will return to the edit menu. Destination entry - Street, intersection and house number If you want to drive to a street in the town you entered as your destination last, you can also select STREET from the destination entry menu. To make it easier to find your street, a long street name may be listed more than once, e. Enter the street name in the edit menu, Select the street name you are looking for from the list.

After you have selected the street, you will access the destination entry menu. The main navigation menu will appear and you can start route guidance to the street selected.

For more information, refer to the section on Route guidance. This will not be possible unless the corresponding data is available on your navigation CD. Select the block of numbers containing the house number. The main navigation menu will appear. Now you can start route guidance. To adapt the route to your preferences, e. For more information, refer to the sections on Route options and Route guidance in this chapter. If there are more than twenty intersections, an editing menu will appear so that you can find the intersection you are looking for more easily.

Enter the name of the intersecting street into the edit menu and switch to the list. Select the desired intersecting street from the list. Now you can select route options in the DSC menu, if desired, and start route guidance to the selected intersection. For more information, refer to the sections on Route options and Route guidance.

Select the town centre you are looking for from the list. If there are more than 20 town centres available in the destination town, an edit menu will appear to allow you to select the town centre you are looking for. Enter the name of the town centre, Activate the list and Select the town centre from the list. The categories are stored in alphabetical order.

Categories for special destinations include e. Not all categories are available for all special destinations and places. The selection of categories in the special destinations menu depends on what is available in the destination area. After you select a category, the list will appear if there are fewer than 20 entries and the edit menu if there are more than 20 entries.

DEST are not connected with any particular place. Categories are available for the entire country and include such destinations as motorway access points, motorway service points, airports and border crossings.

This will also include special destinations in the surrounding area, e. SURROUND , are special destinations in the area surrounding your current vehicle position this function is particularly useful if you are looking for such special destinations as petrol stations, for example.

Enter a town or town centre as your destination. You will access the main navigation menu. Switch to the destination entry menu. A list indicating all of the special destination categories for the destination selected will appear. Select the desired category. If there are fewer than 20 entries available in the category selected, a list will appear.

The special destinations available will appear in alphabetical order, indicating the distance to the destination selected. If there are more than 20 entries available in the category selected, you will first see an edit menu.

Destination entry menu Enter the name of the special destination, Switch to the list and Select the destination you are looking for from the list. Once you have selected and confirmed the desired destination, the main navigation menu will appear. You can start route guidance. Here you are not required to enter a destination first. All you have to know is the name of the special destination you are looking for. A list of supraregional destinations will appear. The supraregional destinations available will depend on the data stored on your navigation CD.

The edit menu will appear. Once you have selected and confirmed the special destination you are looking for, the main navigation menu will appear. You can now start route guidance. Special destinations - Surrounding the destination To select special destinations in the area surrounding your destination, you must first enter a street as your destination. Enter a town and a street as your destination. Select the menu item DEST.

Select the category you are looking for. Enter the name of the special destination, Switch to the list and Select the destination you are looking for from the list.

Special destinations - Surrounding the current location This type of special destination is found in the area surrounding the current location of your vehicle. It is useful when you want to plan a short stop to fill up with petrol, for example. Select the menu item POS. A list displaying all of the special destinations categories currently available in the area surrounding your vehicle location will appear. Destination entry - from the destination memory You can store destinations that you drive to frequently in the destination memory and recall them at a later date for route guidance.

For information on how to store and edit destinations in the destination memory, refer to the chapter entitled Destination memory. For more information, refer to the chapter entitled Destination memory. Select the memory containing the destination you want to recall. You can also activate the Last 10 memory with the hotkey. Select the destination you are looking for.

Destination entry - for a position marker You can also enter the destination in the form of a position marker you have set. A position marker is the vehicle position you have set as a marker during active route guidance or locating.

To set a position marker, a navigation CD must be inserted in the system. Selecting a position marker as your destination You can enter the last position marker set directly for route guidance.

The position marker will be used as your destination for route guidance. The system will switch to the main navigation menu and you can now start route guidance.

You can also activate the route guidance menu with the hotkey. The route guidance menu will appear. The route will be calculated. Depending on how far you are from your destination, this can take several seconds. After route calculation is complete, you will hear the first spoken driving recommendation.

The top line of the route guidance menu will display the name of the street you are currently driving on or the name of the next street into which you must turn off.

The visual driving recommendations appear in the symbol field in the left-hand part of the display. You can switch between 2D and 3D to display the driving recommendations. To switch back and forth between the display modes, Press OK 8 until the display changes. In the centre you will see a bar graph which indicates the distance to the next change in direction. On the right-hand side of the display, you can choose between a display of the remaining driving time to your destination or the estimated time of arrival.

The remaining distance to your destination appears below the time display. The right-hand, bottom line in the display area indicates the active audio source. If the CD changer optional is active, the number of the CD currently playing and the track number or the track number and the elapsed playing time of the track will appear here. Route guidance menu, 3D display Note: While the route guidance menu is active, the six softkeys and the rocker switch 7 have the same functions as in the main menu of the audio source which is active in the background.

This means that you can activate the most important main functions of the active audio source at any time without leaving the route guidance menu. Switching the audio source You can switch your audio source at any time during route guidance. Press TU or CD. The main menu for radio or CD changer operation will appear. It is not possible to activate the CD changer operation menu unless a CD changer is connected and ready to operate.

It is not possible to activate CD operation for the integrated CD player during route guidance. Select a different radio station or a different CD track, for example.

When you press ESC 9, you will be prompted to confirm your selection. If you switch the system off during active route guidance, the data for route guidance will remain stored for another 30 minutes. During this time you can continue your trip with route guidance.

After 30 minutes have passed, you must start route guidance again. When NO MAP route guidance is active, NO MAP will appear in the top line of the display and the distance to your destination as the crow flies will appear in the symbol field on the left.

In addition, the display will also indicate the direction to the destination. For technical reasons it may take several minutes for route guidance to resume properly with spoken driving recommendations and the pictograms after the CDROM has been re-inserted into the CD drive. This time is required for the system to clearly identify the current vehicle position. In densely built-up areas with a closely woven network of roadways, the locating function may not always be accurate until the system is able to orient itself clearly.

As a rule, the information is divided into categories. As this information depends on the data stored in the travel guide on your CD, it is not possible to provide an exact description here.

If there is only one travel guide on the CD, the name of the travel guide will appear directly in the main navigation menu, e. If there is more than one travel guide on the CD, a selection menu listing the travel guides will appear first. Select a travel guide. You might be required to enter the name of the town or city for which you want the information in an edit menu for selecting the town.

Select the category for the information you require. The route list which has been calculated will appear. When you have finished with the list, Press ESC 9 to quit the menu. Locating mode In the locating mode, the name of the street you are currently travelling on will appear in the top line of the menu. The symbol field shows a compass symbol indicating due north. Since the locating mode is not route guidance, the distance to the destination is not indicated.

If GPS time is available, the current system time will appear in the right-hand part of the display. Note: You can also activate the locating mode with the hotkey. You can view the contents of the destination memory sorted either alphabetically or according to the criteria you have chosen. Storing a destination in the destination memory You can store the currently active destination, or after route guidance has ended, the destination last entered for route guidance in the destination memory.

Note: You can also activate the destination memory with the hotkey. An edit menu which allows you to enter a short name will appear. Enter a short name for the destination and confirm it. If you do not want to give the destination a short name, Select the or symbol immediately and press OK 8, Press OK 8 for longer than two seconds.

The destination will be stored with its complete name. You can change the name for the destination at any time. An alphabetical list containing all of the destinations stored in the destination memory will appear. An edit menu will appear. Sorting destinations manually You can also sort the destinations in the destination memory manually.

Then it is possible to activate this manually sorted list to enter a destination for navigation from the destination memory. Move the selection bar to the entry you want to move and Press OK 8.

A marker will appear in front of the entry. Move the destination to its new position on the list and Destination memory menu Press OK 8. Repeat this process until all of the entries are positioned as you want them. Deleting destinations from the destination memory It is possible to delete the memory containing the last 10 destinations, individual destinations and all of the destinations in the destination memory.

This will not function unless a navigation CD is inserted in the system. A menu containing the following selections will appear: LAST10, the memory containing the last 10 destinations will be deleted. Not possible unless the LAST 10 memory has been activated. After you have selected the option you want, you will be prompted to confirm your selection. Confirm it or return to the previous menu.

GPS status This displays the number of GPS satellites which the system is currently able to receive and the geographical location. Note: You can also activate the GPS status with the hotkey. You could suffer a fatal electrical shock! Instead, contact your nearest service center! Translate this page:. Blaupunkt vw gamma 1 torz bluetooth bemenet. Similar manuals:. If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test or write your question to the Message board without registration.

You can write in English language into the forum not only in Hungarian!